How To Hang A Wreath On A Window

Download Article

I of the most classical holiday decorations is an evergreen wreath hanging in a glowing window. Unlike doors and walls, y'all cannot hammer a nail into the window. Suction cups are great for hanging items on drinking glass, merely they are not strong enough for most wreaths. Luckily, there are lots of ways to hang a wreath on a window without damaging the drinking glass or worrying about the wreath falling off. Y'all can even use these methods to hang other types of wreaths, regardless of the season!

one
Go a an adhesive hook meant for windows. You can find these hooks in home improvement stores. They are oftentimes labeled as "Control Hooks" and come up with a strip of adhesive. Make sure that you become a hook specifically labeled for windows.
- If the window claw comes in multiple sizes, get the largest ane. A smaller ane may not be sturdy enough to support a wreath.
- These hooks can typically only carry 4 pounds (i.8 kg). If your wreath is heavier than that, this method would not be a proficient selection for you.
2
Clean your window with rubbing booze. Decide which side of your window you will be hanging the wreath on, then wipe it down with a textile dipped in rubbing booze. You exercise not need to make clean the entire window—just the function where the hook volition get.^[1]
- This is very important, as it will remove any dirt or oils that may forbid the claw from properly adhering.
Advertisement
3
Remove the liner on the back of your command hook's agglutinative strip. Find the side of the strip that has the blackness-and-white liner. If y'all can't find it, look for something that says "window." Peel the liner off, and leave the other one in place.^[2]
- Be conscientious not to touch the adhesive. The more y'all touch on it, the less tacky it will be.
4
Press the strip against the window, then rub information technology with your finger. Decide where you will hang the wreath, then printing the strip against the drinking glass, adhesive-side-down. Make sure that it is oriented vertically, then rub the strip with your finger once more for some other 30 seconds.^[3]
- Well-nigh strips will have a tab on ane cease. Make sure that this tab is facing downwards.
5

Remove the 2d liner and place the claw against it. Make sure that the hook is oriented vertically. Press the claw firmly against the window for 30 seconds.^[iv]
6

Await one hour. Practise not get impatient and hang your wreath right subsequently securing the claw. The adhesive needs this fourth dimension to bond. If you hang the wreath besides presently, the hook may autumn off.^[v]
vii

Hang the wreath over the hook. If the wreath is too thick for the hook, thread some ribbon through it start, then necktie both ends together to brand a loop. Slip the ribbon loop over the hook.
eight
Pull on the tab when yous want to remove the hook. Well-nigh adhesive strips on control hooks will have a picayune tab on the lesser. Remove the wreath kickoff, then pull direct downwards on the tab. Stretch it to nigh 12 inches (xxx cm), then pull the hook off. Peel the agglutinative strip off the window.^[6]
- If in that location is any gunky residue, wipe it off with some white vinegar or a goo remover (i.east.: Goo Gone).
- If you tin't find the tab on the strip, endeavour dripping some rubbing alcohol, acetone, or rubbing alcohol down the glass, correct above the hook. This should deliquesce the adhesive.
Advertisement

1
Go a magnetic window hanger for wreaths. You tin find these online, the floral section of an arts and crafts store, and some home improvement stores. The advantage to these types of hangers is that they accept a hook on both sides, assuasive you to hang a wreath indoors and out.^[7]
- Magnetic window hangers only piece of work on single-pane windows.^[8]
- Most magnetic wreath hangers tin can hold up to 10 pounds (4.5 kg). Double-check the parcel to find out exactly how much yours can hold.
two
Hold one of the magnets against the glass where yous want the wreath. You can do this yourself, or you can ask a helper to do it for you. If you don't take anyone to aid yous, secure the magnet to the glass with a strip or 2 of potent tape; don't worry, y'all'll remove the tape later.
- If your magnets came stuck together, you will demand to pull them apart first.
- Use a strong tape that can back up the weight of the magnet, such as packaging tape or duct tape.
3
Place the other magnet against the other side of the window. The magnets are very strong, and so the two halves volition attract each other through the drinking glass.^[nine] If yous taped the outset magnet to the drinking glass in the previous step, you tin can remove the tape now.
- If the tape left some remainder, wipe it off with some white vinegar or an agglutinative remover (i.e.: Goo Gone).
- The magnets take a protective coating, so they should not scratch the drinking glass.
4

Hang the wreath onto the hook. Choose a side of the window for the wreath to go on, then hang the wreath over the hook. If your wreath is likewise thick for the hook, loop some ribbon around it first, so slip the ribbon over the hook.
five

Hang another wreath on the other side of the window, if desired. Each magnet has a hook on it, so yous can hang a wreath on each side of the window. If you choose to do this, however, it could exist a good idea to use identical wreaths. You will still be able to come across the wreaths through the window. If they are different, they may disharmonism.

Advertizing

1

Ensure that your window tin can open from the top. This will allow y'all to push the wreath out through the top of the window, and secure it to the top of the frame. The wreath will hang in front of the window. A double sash window would exist ideal, but a double hung window may also work.
2
Cut iv to 5 anxiety (1.2 to 1.five chiliad) of wide, outdoor ribbon. Cull a two ane⁄two-inch (6.four-centimeter) wide ribbon that matches your wreath, and then cutting it downwardly to 4 to 5 anxiety (1.2 to 1.five m). Outdoor ribbon will be the best because you will exist closing the window on it.^[10]
- If you lot can't find outdoor ribbon that you lot like, use a ribbon made from a sturdy material, such as velvet or grosgrain. Avoid delicate materials, such every bit sheer or lace.
iii
Hot mucilage one end of the ribbon effectually your wreath. Coat the cease of your ribbon with hot glue and place information technology confronting the back of your wreath. Make sure that the stop of the ribbon is pointing towards the acme/outer edge of the wreath, and that the rest of the ribbon is pointing towards the center.^[11]
- If yous don't have hot mucilage, you can apply a U-shaped florist's pin instead.
4
Wrap the ribbon effectually the top of the wreath twice. Thread the ribbon through the middle of the wreath. Pull information technology up across the front and over the top. Practise this step twice, stopping when you reach the height over again.^[12]
- Y'all can secure the ribbon to the forepart of the wreath with another drib of hot mucilage for additional security.
5
Add together a bow to the peak of the wreath for a nicer finish, if desired. If you have whatsoever ribbon leftover on the spool, you can tie it into a fancy bow, then hot mucilage it to the forepart of the wreath, right over the wrapped ribbon. Yous can also buy a pre-made matching bow from the shop, and utilise that instead.^[13]
- The ribbon and floral departments of arts and crafts stores often sell pre-fabricated bows.
- Alternatively, you can place the bow at the lesser of the wreath.
six
Open the window and push button the wreath through it. You only need to open up the window broad plenty to fit the wreath through—about i foot (30 cm) will be enough for most wreaths. Be sure to agree onto the ribbon tightly and then that you don't driblet the wreath.^[14]
- Yous are hanging the wreath on the outside of the window. If you lot desire the wreath to exist on the inside, you will need to get out a ladder, and work from the exterior of your home.
seven
Adjust the length of the ribbon, then pin it to the window frame. Pull downwards on the ribbon until the wreath is hanging where you want it to be. Push button a thumbtack or pushpin through the ribbon and into the frame.^[15]
- Brand certain that you stick the pivot to the side of the frame. If you pin information technology to the very superlative, it volition get in the style when you shut the window.
- If you lot have vinyl or metal window frames, necktie a large knot into the ribbon instead.^[16]
8
Shut the window. This will aid give the ribbon actress security and preclude it from slipping or sliding. Proceed the window closed as long every bit the wreath is upwards. Even if you pinned the wreath, there is a pocket-size chance that it may come loose.
- If you tied a knot onto your ribbon, make certain that it is on the inside of the window, otherwise the wreath will fall.
Advert

Ask a Question

200 characters left

Include your email accost to become a message when this question is answered.

Submit

Advertising

If your wreath is small and light enough, you tin can stick a big suction loving cup to your window, and use that instead.
Become wreaths that are most 10 inches (25 cm) narrower than your windows.^[17]
If you lot are hanging your wreath outside, tie some fishing line to the bottom of the wreath, and so secure the other end to the bottom of the frame.^[xviii]
Decorate your wreath with lights and ornaments earlier hanging it upwards. Battery-operated lights will work the best.
Place some electrical or bombardment-operated candles in your window for a magical glow.
If your wreath is sparse enough, you may be able to hang it directly from the hook.
If your wreath is very dumbo, yous will demand to tie a loop of ribbon to information technology kickoff, and then hang the ribbon from the hook.

Thanks for submitting a tip for review!

Things You'll Need

Rubbing alcohol
Adhesive hook for windows
Wreath

Magnetic window hanger
Helper or strong tape
Wreath

Wide ribbon
Hot glue or U-shaped pins
Thumbtack or pushpin
Wreath

About This Article

Article Summary X

To hang a wreath on a window using an adhesive claw, start by cleaning the glass with rubbing booze so the agglutinative will create a secure seal. Next, remove the liner on the back of the claw'south adhesive strip, taking intendance non to touch the sticky role, and press the strip against the drinking glass for 30 seconds. Then, remove the 2nd liner, identify the hook against it, and printing the hook against the window for 30 seconds. Finally, let the adhesive set for 1 hr earlier hanging your wreath on the claw. For tips on using magnetic hangers, read on!

Did this summary help you?

Thanks to all authors for creating a folio that has been read 50,218 times.